Illinois Roofing Exam

Steep-Slope Roofing on the Illinois Roofing Exam: What It Covers and What to Study

A steep-slope roof is any roof with a slope greater than 3:12, and Steep-Slope Roofing Systems accounts for 20 of the 80 questions on the Illinois Residential roofing exam. Here is what the section covers, how the roof systems differ, and what the exam asks about each one.

Since 2010 · ★★★★★ 5.0 · 210+ Google reviews

What is a steep-slope roof?

A steep-slope roof is a roof system with a slope greater than 3:12. A roof at exactly 3:12 is not steep-slope. It is low-slope.

Slope is the rise of the roof compared to its run, in inches. For the exam there are only two categories, low-slope and steep-slope, and several rules change depending on which side of that line the roof is on.

Low-slope up to and including 3:12 Steep-slope greater than 3:12 Run: 12 in. Run: 12 in. 3 in. 4 in. 3:12 4:12
A 3:12 roof is still low-slope. Steep-slope starts above 3:12, which means 4:12 and greater.

A steep-slope roof is typically made of individual pieces of material installed shingle-fashion over underlayment. For the numbers behind slope, see our page on Illinois roofing exam math.

How many steep-slope questions are on the Illinois roofing exam?

Steep-Slope Roofing Systems accounts for 20 of the 80 questions on the Illinois Residential roofing exam. That is one question in four.

The exam is closed book and you need a score of 70. The questions follow the reference books, so what counts is the book answer, even where your own crew does it differently. See what is on the Illinois roofing exam for the full breakdown.

What roof coverings are used on steep-slope roofs?

Steep-slope roofs are covered with asphalt shingles, metal panels, tile, wood shakes, wood shingles or slate.

  • Asphalt shingles. Three-tab strip shingles and dimensional (architectural) shingles.
  • Tile. Made of clay or concrete.
  • Wood shakes and wood shingles. Two different products, made two different ways.
  • Slate. Natural, heavy and long-lasting.
  • Metal panels. Architectural and structural.

The exam asks about each one: how it is fastened, what goes under it, and the lowest slope it can go on.

What does underlayment do on a steep-slope roof?

Underlayment is the layer between the roof deck and the roof covering. It protects the deck until the covering is on, and it is the backup if water gets past the covering.

There are three basic types: asphalt-saturated felt, rubberized asphalt and non-bitumen synthetic. Felt is water-resistant, not waterproof.

What the exam asks. How far each course of underlayment has to overlap the one below it, and how that changes on a low-slope roof. It also asks whether drip edge goes over or under the underlayment, and the answer is not the same at the eave as it is at the rake.

What are asphalt shingles made of, and how are they fastened?

An asphalt shingle has four basic components: surfacing, asphalt, fillers and a reinforcing mat. Each one is there for a reason, and the exam asks what each one does.

Shingles are fastened with roofing nails, and a starter course goes down along the eave before the first course of shingles.

What the exam asks. How many nails a standard strip shingle takes, when more are required, what kind of nail to use, and what the starter course is for.

What is ice-dam protection?

Ice-dam protection is a water-resistant membrane installed along the eaves in cold climates. It keeps water from backing up under the roof covering when ice builds at the edge of the roof.

What the exam asks. How far up the roof the membrane has to extend, where that measurement starts, and how the distance changes with slope. Pay attention to how the distance is measured. That detail is where people lose the point.

What are the types of roof valleys?

An asphalt shingle roof can have a woven valley, a closed (cut) valley or an open valley. Tile roofs use open valleys only.

A valley is created where two sloping roof planes meet. Water from both planes runs toward the valley and then along it.

Roof coveringValley types
Asphalt shinglesWoven, closed (cut) or open
TileOpen only. Tile cannot bend.
Wood shakes and shinglesOpen, or closed (mitered)

The exam asks how wide the valley metal has to be for each roof covering, and which valley shape is recommended.

What flashing goes around a chimney?

A chimney gets apron flashing on its downslope side and step flashing up its sides, and a wide chimney gets a cricket on its upslope side.

  • Apron flashing. On the downslope side of the chimney.
  • Step flashing. On the sides, one piece at the end of each course.
  • Cricket. A small framed peak behind the chimney that splits the water around it.

The exam asks for the size of the step flashing and how wide a chimney has to be before it needs a cricket.

What does the exam ask about wood, tile and slate?

The exam asks how each of these roofs is fastened, the lowest slope it can go on, and the one property that causes it the most trouble.

  • Wood. Shakes are split and shingles are sawn, so they are not the same product. Know the minimum slope and how many fasteners each piece takes.
  • Tile. Clay and concrete tile soak up different amounts of water, and that decides which one handles freezing better. Know what battens and eave closures are for.
  • Slate. Weight is the biggest challenge of a slate roof. Know which nail is preferred, and why.

How do you study steep-slope roofing for the exam?

Learn it one roof system at a time, in the order the roof goes on: deck, underlayment, edge metal, flashing, then the roof covering.

In class we go through each system step by step, with the number the exam wants for each one, until the order of install is automatic. Then you drill it with First Try before exam day.

Want to see where you stand today? Take our free 10-question practice test, or see what is on the Illinois roofing exam.

Common questions

What slope is considered a steep-slope roof?

A steep-slope roof has a slope greater than 3:12. A roof with a slope up to and including 3:12 is low-slope.

How many steep-slope questions are on the Illinois Residential roofing exam?

Steep-Slope Roofing Systems accounts for 20 of the 80 questions on the Residential exam. The exam is closed book and you need a score of 70.

What roof coverings count as steep-slope?

Asphalt shingles, metal panels, tile, wood shakes, wood shingles and slate.

What are the types of roof valleys?

An asphalt shingle roof can have a woven valley, a closed (cut) valley or an open valley. Tile roofs use open valleys only.

What steep-slope topics should I study for the exam?

Underlayment and drip edge, asphalt shingle parts and fastening, ice-dam protection, valleys, chimney and step flashing, and wood, tile and slate roofs.

Learn more: our Illinois roofing exam prep course, or call (773) 635-0099.

Get Your Illinois Roofing License

Live in Rosemont or on Zoom. We teach to the test and guide you through the paperwork.