Illinois Roofing Exam

Illinois Roofing Exam Math: Slope, Squares and Roof Area, Step by Step

The math on the Illinois roofing exam is estimating: slope, run, rafter length, roof area, squares, perimeter, waste and labor cost. It is multiplication, division and one table lookup, and you may bring a basic calculator. Here is each calculation with the formula and a worked example.

Since 2010 · ★★★★★ 5.0 · 210+ Google reviews

How much math is on the Illinois roofing exam?

The math on the Illinois roofing exam is estimating math: slope, run, rafter length, roof area, squares, perimeter, waste and labor cost. It is multiplication, division and one table lookup. There is no algebra and no trigonometry, and you may bring a basic calculator.

The exam is closed book, so the part that trips people up is not the arithmetic. It is knowing which number to start with and what order to work in. Every calculation below follows the same pattern: find the run, find the slope factor, then multiply.

What is roof slope?

Roof slope is the rise of the roof in inches for every 12 inches of run. A roof that rises 6 inches for each 12 inches of run is written “6:12” or “6 in 12.”

Run: 12 inches Rise:6 inches Roof surface (rafter)
A 6:12 slope. The roof rises 6 inches for every 12 inches of run.

For the exam, there are only two slope categories:

  • Low-slope: a roof with a slope up to and including 3:12.
  • Steep-slope: a roof with a slope greater than 3:12.
Inches to feet. Roof math is done in feet, so convert inches to a decimal first: divide the inches by 12. Six inches is 6 ÷ 12 = 0.5 feet. Nine inches is 0.75 feet.

How do you find the run of a roof?

On a gable roof, the run is half the width of the building. Divide the width by two.

Run = Width ÷ 2

Run: 15 ft Run: 15 ft Building width: 30 ft Rafter Ridge
Run is half the building width. A 30-foot-wide gable has a 15-foot run on each side.

A building 30 feet wide has a run of 15 feet. The run is a flat, horizontal distance. It is not the length of the roof surface. That is the next step.

What is a slope factor, and how do you find rafter length?

A slope factor is the number you multiply the run by to get the true length of the sloped roof surface, called the rafter length. The steeper the roof, the bigger the factor.

Rafter Length = Run × Slope Factor

The factor comes from the right triangle in the slope drawing above. The roof surface is the long side of that triangle, so it is always longer than the run underneath it. You do not have to work the triangle out by hand. You look the factor up.

Roof slopeSlope factor (rafter length)Category
1 in 121.004Low-slope
2 in 121.014Low-slope
3 in 121.031Low-slope
4 in 121.054Steep-slope
5 in 121.083Steep-slope
6 in 121.118Steep-slope
7 in 121.158Steep-slope
8 in 121.202Steep-slope
9 in 121.250Steep-slope
10 in 121.302Steep-slope

Example: a 6:12 roof with a 15-foot run. 15 × 1.118 = 16.77 feet of rafter.

Hips and valleys run at an angle across the roof, so they are longer than a rafter and use their own, larger factor. Use the hip and valley column for those, never the rafter column.

How do you calculate the area of a sloped roof?

To calculate the area of a gable roof, find the rafter length, multiply it by the length of the building, then double it for the two sides.

  1. Find the run. Width ÷ 2.
  2. Find the rafter length. Run × slope factor.
  3. Find one side. Rafter length × building length.
  4. Double it. A gable has two sides.

Example: a building 30 feet wide and 40 feet long with a 6:12 roof.

StepMathResult
Run30 ÷ 215 ft
Rafter length15 × 1.11816.77 ft
One side16.77 × 40670.8 sq ft
Both sides670.8 × 21,341.6 sq ft

The flat footprint of that building is only 1,200 square feet. Forget the slope factor and you come up 141.6 square feet short.

What is a roofing square?

A roofing square is an area 10 feet by 10 feet, which is 100 square feet. To convert roof area to squares, divide the square feet by 100.

Squares = Roof Area in Square Feet ÷ 100

The 1,341.6 square foot roof above is 1,341.6 ÷ 100 = 13.42 squares.

What is the difference between net and gross roof area?

Net roof area is the area of the roof that will be covered with roofing material. Gross roof area is the net area plus the extra material needed at the ridge, hips and valleys, starter courses, and the waste allowance.

For a roof that is not a simple rectangle, there are two ways to get the net area:

  • Positive method. Divide the roof into rectangles, then add them up.
  • Negative method. Extend the roof lines into one large rectangle, then subtract the parts that are not roof.
Not roof20 x 10 50 ft 30 ft 30 ft 20 ft Roof area
The same roof, measured two ways. Both methods give 1,300 square feet.
MethodMathResult
Positive(50 × 20) + (30 × 10)1,300 sq ft
Negative(50 × 30) − (20 × 10)1,300 sq ft

Use whichever is faster for the shape in front of you. If both give the same answer, you have checked your own work.

How do you calculate roof perimeter?

Perimeter is the total outer linear measurement of a roof, and it is what you use to measure drip edge. For a roof with no recesses, add the length and the width and multiply by two, or simply add all four sides.

Perimeter = 2 × (Length + Width)

The perimeter of a sloped roof is not the same as the perimeter of a flat roof on the same building. On a gable, the sloped edges are rafter lengths, not half the building width.

Example: the same 30 by 40 foot building with a 6:12 roof. Four sloped edges at 16.77 feet is 67.08 feet. Two eaves at 40 feet is 80 feet. The perimeter is 147.08 feet, not the 140 feet you get from the flat footprint.

What is a waste allowance?

A waste allowance is the material that gets used up in the installation and never ends up as finished roof. On a shingle roof, most of it is at the hips and valleys, where shingles are cut.

Waste at hips and valleys is figured per linear foot. You find the length of each hip and valley, add them up, and multiply by the waste factor, which gives you square feet of waste. Hips and valleys have different factors, so keep the two totals apart until after you multiply.

  1. Find the run.
  2. Find the hip or valley length. Run × the hip and valley factor for that slope.
  3. Total the linear feet of hips, and separately of valleys.
  4. Multiply each total by its waste factor and add the two results.

The waste factors are given to you on the test. What you need to know is how to use them.

How do you calculate labor cost and job duration?

The labor unit price is the installer’s cost for each unit of production. You find it by dividing the total crew cost by the total crew production.

Labor Unit Price = Total Crew Cost ÷ Total Crew Production

Example: a crew that costs $50 an hour works an 8-hour day and installs 8 squares. $50 × 8 = $400 a day. $400 ÷ 8 squares = $50 per square.

Job duration is the total material divided by the production rate.

Job Duration = Total Squares ÷ Squares Per Day

A 12-square roof with a crew that installs 8 squares a day takes 12 ÷ 8 = 1.5 days.

How far from the building should a ladder be set?

Set the base of the ladder 1 foot out from the base of the building for every 4 feet of vertical rise. The top of the ladder must extend 3 feet above the working area.

4 ft out 16 ft of rise 3 ft above the edge
One foot out for every four feet of vertical rise, and three feet above the working area.

For 16 feet of vertical rise, the base sits 16 ÷ 4 = 4 feet out. This one is safety, not estimating, but it is the same kind of question: one rule and one division.

Can you use a calculator on the Illinois roofing exam?

Yes. You may bring a non-programmable, non-printing, solar- or battery-powered portable or pocket calculator. No other calculators, computers or electronics are permitted. Also bring two sharpened Number 2 pencils and your printed exam admission letter.

The exam is closed book, so the formulas above have to be in your head when you walk in. In class we work these problems step by step until the order is automatic, then you drill them with First Try before exam day.

Want to see where you stand today? Take our free 10-question practice test, or see what is on the Illinois roofing exam.

Common questions

Is there math on the Illinois roofing exam?

Yes. It is estimating math: slope, run, rafter length, roof area, squares, perimeter, waste and labor cost. It is multiplication, division and one table lookup.

Can I use a calculator on the Illinois roofing exam?

Yes. You may bring a non-programmable, non-printing, solar- or battery-powered portable or pocket calculator.

How many square feet are in a roofing square?

A roofing square is 10 feet by 10 feet, which is 100 square feet. Divide the roof area in square feet by 100 to get squares.

How do you find rafter length?

Multiply the run by the slope factor. On a gable roof the run is half the building width. A 6:12 roof with a 15-foot run has a rafter length of 15 x 1.118 = 16.77 feet.

What is the difference between a low-slope and a steep-slope roof?

A low-slope roof has a slope up to and including 3:12. A steep-slope roof has a slope greater than 3:12.

How far out should the base of a ladder be?

One foot out from the base of the building for every 4 feet of vertical rise, with the top extending 3 feet above the working area.

Learn more: our Illinois roofing exam prep course, or call (773) 635-0099.

Get Your Illinois Roofing License

Live in Rosemont or on Zoom. We teach to the test and guide you through the paperwork.